此系列低温真空干燥箱适用于在高温下易分解、聚合或变质的热敏性物料的干燥。在干燥前可进行消毒处理、干燥过 程中无任何不纯物混入物料，在制药、食品、化工、电子等行业广泛应用。
将被干燥物料处于真空条件下，进行加热干燥，低温真空干燥箱是利用真空泵进行抽气抽湿，加快了干燥速率。当加 热温度恒定， 提高真空度， 能加快干燥速率。当真空度恒定， 提高加热温度， 能加快干燥速率。既提高真空度， 又提高加 热温度，则大大加快干燥速率。
This series of low temperature vacuum drying oven is suitable for drying heat-sensitive materials that are easy to decompose, polymerize or deteriorate at high temperatures. It can be disinfected before drying, and no impurity is mixed into the material during the drying process, which is widely used in pharmaceutical, food, chemical, electronics and other industries.
The material to be dried is heated and dried under vacuum conditions. The low-temperature vacuum drying oven uses a vacuum pump to pump air and moisture, which speeds up the drying rate. When the heating temperature is constant and the vacuum degree is increased, the drying rate can be accelerated. When the vacuum degree is constant, increasing the heating temperature can speed up the drying rate. If the vacuum degree is increased and the heating temperature is increased, the drying rate is greatly accelerated.

●系统通过控制供热-真空达到平衡，使物料全程处于不溢盘(有监控)的中度~高度沸腾状态;
●物料在沸腾状态下干燥，浸膏块处于疏松多孔状态，粉碎后，细粉堆密度较小，更容易溶解;
●干燥箱通过加热板层的设计，比传统真空箱有更大的加热面积，加热更均匀;
●为便于每一处物料都能同步干燥，它在设计上对加热料用器皿\加热板层的平整度要求更高:
●低温真空干燥箱采用压缩气体形成“气针/气刀”有效刺破/切破结皮，加快浓缩进程，避免爆沸造成的溢盘逃料;
●侧面多通道抽真空/补气，使系统内的真空，在使用板层加热后，依然均匀，同时有效避免了冷凝水回流至物料内，造成 局部不干燥而影响干燥速度;
●可选配 CIP 清洗系统(带蒸汽润洗、浸泡、喷淋等多种清洗模式)。
● The system achieves balance by controlling heat-vacuum, so that the material is in a moderate to high boiling state without overflow (monitored) throughout the whole process;
● The material is dried in the boiling state, and the extract block is in a loose and porous state. After crushing, the density of the fine powder pile is smaller and easier to dissolve;
● Through the design of heating plate, the drying box has a larger heating area and more uniform heating than the traditional empty box;
● In order to facilitate the synchronous drying of each material, it has higher requirements for the flatness of the heating material utensils \ heating plate layer in the design:
● The low-temperature vacuum drying oven uses compressed gas to form a "gas needle/gas knife" to effectively puncture/cut the crust, speed up the concentration process, and avoid the overflow caused by explosion and boiling;
● Side multi-channel vacuum/aeration, so that the vacuum in the system, after the use of plate heating, is still uniform, and effectively avoid condensation water back into the material, causing local drying and affecting the drying speed;
● Optional CIP cleaning system (with steam washing, soaking, spraying and other cleaning modes).